Month: June 2012

Posted on

FEP Shrink Tubing Is Just One of Several Options for Heat Shrink Tubing

When you are looking at heat shrink tubing, you have several different options of tubing available. You can look at PTFE tubing with different heat shrink ratios and wall thicknesses, or FEP shrink tubing which has lower shrink ratios ands it shrinks at a lower temperature than PTFE. You can even look at combination PTFE-FEP shrink melt tubing, which has PTFE on the outside layer and FEP on the inside layer.

Prepare Materials before Applying FEP Shrink Tubing

Before applying FEP shrink tubing, you will want to properly prepare the material being covered. You should wipe off any dirt and dust from the surface area and make sure it is completely dry. Applying heat shrink tubing to dirty or wet materials can result in the tubing not shrinking correctly or forming a tight bond around the material.

Posted on

Different Industrial Applications Use Straightened Wire

Straightened wire is used in different industrial applications for various reasons. This type of wiring can be inserted through different gauges of hypodermic tubing. The outside tubing provides a protective covering for the wire to keep it from being bent or broken, which can be useful when you are using the wiring as a type of push-pull mechanism. You can avoid having wires rubbing against one another since they will be contained within the hypodermic tubing.

Straightened Wire Can Be Used to Make Soft-Walled Tube Firm

It can be difficult securing a tight connection when you are using a soft-walled tube. The tube can bend and twist and not line up correctly in the area where you need to make a connection. You can use straightened wire by inserting it through the tube to help keep the wall firm. This will allow you to make the secure connection with the tubing, and then you just remove the wire when you’re done.

Posted on

Avoid Pre-Drilling Holes by Using Self Tapping Stainless Steel Machine Screws

It can be difficult working with small stainless steel machine screws when you have to worry about pre-drilling holes. For situations where you just want to insert and tighten the screw, you will want to use self tapping screws. Self tapping screws have a sixty degree, sharp tip to make penetrating into different semi-hard materials easy.

You Can Use Stainless Steel Machine Screws by Themselves or With Adhesives and Glues

There are different methods for fastening together different types of materials. You can use adhesives and glues to secure the pieces together. However, adhesives and glues can break down over time, causing the materials to come apart. Another method available is to use stainless steel machine screws. You can use these screws by themselves, or as a secondary method, with adhesives and glues to keep pieces securely fastened together.

Posted on

Applications Which Need to Be Stretched or Moved Can Use NiTinol Wire

NiTinol wire is ideal for applications which need to stretched or moved when they are heated. As the wire is heated through different methods, it returns to its normal shape and size. As the wire cools, it expands and returns to its deformed shape.

NiTinol Wire Is Super Elastic and Has a Low Heating Temperature

One type of NiTinol wire available is super elastic, which requires a lower heating temperature than shape memory NiTinol. This super elastic wire only requires a small amount of heat to return to its normal shape and size, and does not need to be heated with any type of appliance or other device. For instance, you can use this wiring as a suture during surgical procedures. The natural heat of the body will cause the wire to return to its normal shape and size.

Posted on

304 Tubing Is Available In Thin Wall Stainless Tubing Sizes

There are different types of stainless steel tubing available, depending on your requirements. You will see different number designations of 304 and 316 assigned to different tubing products. There is a slight difference in the two types of stainless steel, with 316 having an added component which helps resist corrosion from salt in water and other liquids. Also, 304 tubing is available in different wall sizes, including thin wall stainless tubing.

How Are Regular Wall and Thin Wall Stainless Tubing Different?

The actual gauges of 304 stainless steel tubing will not change, even though the wall size might change. The difference between thin wall stainless tubing and regular wall stainless tubing is the inside diameter of the opening in the tubing. On a regular wall ten gauge tube, the inside diameter is 0.104 to 0.108 inches. On a thin wall ten gauge tube, the inside diameter is 0.112 to 0.116 inches, which is slightly larger than the regular wall tubing.

Posted on

Use a Smaller Nylon Mesh Screen to Remove Small Sediment Particles

It can be difficult to get very fine particles of sediment out of water when your nylon mesh screen is the wrong size. While you can catch larger particles, the small particles will pass right through the mesh screen if the mesh is not small enough. When you want to get rid of these smaller particles, you will need to use a mesh screen with smaller openings.

Nylon Mesh Screen Is Available in Different Size Sheets

Nylon mesh screen comes in different sizes sheets that you can cut down to fit your filtration method. Purchasing mesh screen in sheets is less expensive than purchasing individual custom-cut screening. You can choose from different sizes of sheets ranging from a quarter yard up to a full yard. You will then be able to cut out a variety of different size screens from a single sheet of mesh screen.

Posted on

PTFE Tubing and FEP Tubing Are Both Types of Heat Shrink Tubing

There are different types of heat shrink tubing available for different applications. You can choose between PTFE tubing and FEP tubing. Both types of tubing shrink when heated. The difference between the two types of tubing is the temperature at which the tubing begins to shrink. PTFE tubing has a higher shrink temperature than FEP tubing. You will want to use the type of tubing which is best suited for your application and environment.

PTFE Tubing Can Withstand Higher Temperatures than FEP Tubing

For applications that can become rather hot, it is better to use PTFE tubing in place of FEP tubing because PTFE tubing has a higher shrink temperature. As your device heats up it can cause wiring, cables and other items to heat up as well. PTFE is able to withstand temperatures up to its minimum shrink temperature. This means as long as temperatures remain below this level, you do not have to worry about the tubing melting as your application heats up.

Posted on

PTFE Shrink Tubing Comes In Standard and Custom-Cut Sizes

PTFE shrink tubing, also known by the brand name Teflon shrink tubing, shrinks when it is heated up. This type of tubing can be used to seal and secure different types of connections, wiring and cables. Shrink tubing comes in different sizes including standard four-foot lengths as well as custom-cut sections for specific applications.

PTFE Shrink Tubing Has a Minimum Shrink Temperature

PTFE shrink tubing has to be heated up in order for it to shrink. The most common type of tool used to apply heat to the shrink tubing is a heat gun. A heat gun is able to generate the required level of heat that is needed to shrink the tubing. PTFE tubing requires a minimum shrink temperature in the range of 654 to 670 degrees Fahrenheit.

Posted on

Different Industrial Applications Use Straightened Wire

Straightened wire is used in different industrial applications for a variety of purposes. This type of wiring can be inserted through different gauges of hypodermic tubing. The outside tubing provides a protective covering for the wire to keep it from being bent or broken. This type of setup can be used when you are using the wiring in a type of push-pull mechanism. You can prevent the wires from rubbing against one another since they will be contained within the hypodermic tubing.

Straightened Wire Can Be Used to Make Soft-Walled Tubes Firm

It can be difficult securing a tight connection when you are using a soft-walled tube. The tube can bend and twist and not line up correctly in the area where you need to make a connection. You can use straightened wire by inserting it through the tube to help keep the wall firm. This will allows you to make the secure connection with the tubing. You can then remove the wire afterwards.

Posted on

Avoid Pre-Drilling Holes by Using Self-Tapping Stainless Steel Machine Screws

It can be difficult working with small stainless steel machine screws when you have to worry about pre-drilling holes. For situations where you just want to insert and tighten the screw, you will want to use self-tapping screws. Self-tapping screws have a sixty degree sharp tip to make penetrating into different semi-hard materials easy.

You Can Use Stainless Steel Machine Screws by Themselves or With Adhesives and Glues

There are different methods for fastening together different types of materials. You can use adhesives and glues to secure the pieces together. It is important to remember, however, that adhesives and glues can break down over time. This will cause the materials to eventually come apart. Another method is to use stainless steel machine screws. You can use these screws by themselves or as a secondary method with adhesives and glues to keep pieces securely fastened together.